Stainless Bulkhead - 1/2 in. FPT x 1/2 in. MPT

H726

Stainless Bulkhead - 1/2 in. FPT x 1/2 in. MPT

H726

$16.99 & FREE Shipping on orders over $59 OR $7.99 flat rate shipping.

QUANTITY

In Stock

Delivers to ( change ) by as part of our Fast & Free Shipping.
Faster Shipping Available. Details.

Returns

60 day no hassle return policy. Details

Item #	H726
Shipping	Eligible for Free Shipping Program
Availability	California - In Stock Pennsylvania - In Stock
Weight	0.50 LBS

Description

This stainless steel bulkhead is 1/2" FPT x 1/2" MPT with a flat, thick rubber washer that makes is very easy to install on most kettles. We use this bulkhead on our weldless spigot. You will need to drill a 1" hole to install the bulkhead.

Item #	H726
Shipping	Eligible for Free Shipping Program
Availability	California - In Stock Pennsylvania - In Stock
Weight	0.50 LBS

Documents

Installation Instructions

Community Q&A

Questions that need answers | My Posts

Start typing your question and we'll check if it was already asked and answered. Learn More

Browse 7 questions Browse 7 questions and 56 answers

Why did you choose this?

MoreFlavor Store

Mash Tun

Jedidiah Walkup on Jun 24, 2022

Other sites didn't have this item

Dale E C on Feb 8, 2022

Removing brass fittings from mash tun

Roger S on Oct 29, 2021

I need

Edward S on May 13, 2021

Need to add tell fudge to mash tun

Adam Peppas on Feb 6, 2021

Cooler mash tun conversion

philc on May 18, 2020

Cooler Mash Tun Conversion

Ron B on Mar 16, 2020

to retro my existing setup

Eric K on Jan 25, 2020

Hobby Maple syrup project

Thomas P on Dec 24, 2019

Need a replacement for my mash run.

David M on Dec 10, 2019

I wouldâ€™ve preferred - 1/2in. MPT x 1/2in. MPT

dave m on Sep 5, 2019

Modifying cooler mash tun.

Christopher M on Mar 6, 2019

To add a whirlpool arm

Shannon W on Feb 5, 2019

I have two and want more...

Chuck S on Oct 8, 2018

Updating equipment

Valued C on Aug 27, 2018

bulkhead for mash tun fittings

Jeff R on Feb 24, 2018

Easy to add to your pot .

Kevin McMullin on Feb 3, 2018

Mash Tun

Jedidiah Walkup on Jun 24, 2022

convenience

Kevin P on Mar 1, 2022

Other sites didn't have this item

Dale E C on Feb 8, 2022

converting a rectangular cooler to a mashtun

Anthony J S on Dec 17, 2021

Removing brass fittings from mash tun

Roger S on Oct 29, 2021

Inside/outside threading

Michael Z on Oct 14, 2021

I need

Edward S on May 13, 2021

for ease of cooled wort transfer.

Keith R on Mar 18, 2021

Need to add tell fudge to mash tun

Adam Peppas on Feb 6, 2021

Connecting ball valve and pickup tube in a keggle

Bryce Brownfield on Oct 5, 2020

Cooler mash tun conversion

philc on May 18, 2020

To add a strainer to brew kettle

Jeffrey K on May 2, 2020

Cooler Mash Tun Conversion

Ron B on Mar 16, 2020

didn't want to weld keggle

Chris C on Feb 13, 2020

to retro my existing setup

Eric K on Jan 25, 2020

looks better quality than current

J.W. van der M on Jan 16, 2020

Hobby Maple syrup project

Thomas P on Dec 24, 2019

have bought before -- after years still haven't had to change the gasket on HLT

David Johnston on Dec 12, 2019

Need a replacement for my mash run.

David M on Dec 10, 2019

These are awesome.

MICHAEL D on Nov 19, 2019

I wouldâ€™ve preferred - 1/2in. MPT x 1/2in. MPT

dave m on Sep 5, 2019

Whirlpool

Kenneth Graley on May 4, 2019

Modifying cooler mash tun.

Christopher M on Mar 6, 2019

Want to convert my cube cooler

John M on Feb 12, 2019

To add a whirlpool arm

Shannon W on Feb 5, 2019

Going on a new keggle I am converting to a mash tun

Chris R on Dec 20, 2018

I have two and want more...

Chuck S on Oct 8, 2018

These are my favorite bulkheads and the only ones I'll use. Sturdy and seals well. I put gaskets on both sides and I've never had a leak.

Douglas Nelson on Sep 19, 2018

Updating equipment

Valued C on Aug 27, 2018

I need it

Michael C on Aug 21, 2018

bulkhead for mash tun fittings

Jeff R on Feb 24, 2018

Good Product

John P R on Feb 5, 2018

Easy to add to your pot .

Kevin McMullin on Feb 3, 2018

Needed to build a cold tank.

LUIS GABRIEL GALLARDO R on Jan 15, 2018

convenience

Kevin P on Mar 1, 2022

converting a rectangular cooler to a mashtun

Anthony J S on Dec 17, 2021

Inside/outside threading

Michael Z on Oct 14, 2021

for ease of cooled wort transfer.

Keith R on Mar 18, 2021

Connecting ball valve and pickup tube in a keggle

Bryce Brownfield on Oct 5, 2020

To add a strainer to brew kettle

Jeffrey K on May 2, 2020

didn't want to weld keggle

Chris C on Feb 13, 2020

looks better quality than current

J.W. van der M on Jan 16, 2020

have bought before -- after years still haven't had to change the gasket on HLT

David Johnston on Dec 12, 2019

These are awesome.

MICHAEL D on Nov 19, 2019

Whirlpool

Kenneth Graley on May 4, 2019

Want to convert my cube cooler

John M on Feb 12, 2019

Going on a new keggle I am converting to a mash tun

Chris R on Dec 20, 2018

These are my favorite bulkheads and the only ones I'll use. Sturdy and seals well. I put gaskets on both sides and I've never had a leak.

Douglas Nelson on Sep 19, 2018

I need it

Michael C on Aug 21, 2018

Good Product

John P R on Feb 5, 2018

Needed to build a cold tank.

LUIS GABRIEL GALLARDO R on Jan 15, 2018

how long is the shank? I'm wondering if i can use this in an igloo cooler

Carl Rustic on Jan 24, 2018

BEST ANSWER: The shank is 1-7/8" long. This is the same bulkhead we use on our Rubbermaid cooler mash tuns and hot liquor tanks.

Reply
Inaccurate
Patrick T Staff on Jan 25, 2018

My bulkhead leaks if i put the gasket on the inside, no matter how soft or tight I crank it down. If I put it on the outside it doesn't leak at all, but since it's for a brew kettle, I'm wondering if it will melt from the heat of my propane burner. Any insight?

Jared Wyatt on Feb 8, 2018

BEST ANSWER: This gasket will stand up to the heat for a long while provided the flames don't lick it directly for too long on a given day. It is made of a soft silicone rubber that can withstand temperatures over 400 degrees momentarily, however continued exposure will eventually cause it to char and potentially dry out.

Reply
Inaccurate
Malcolm lieban Staff on Jun 4, 2020

Reply
Inaccurate
Malcolm lieban Staff on Jun 4, 2020

Hi Jared, as you've discovered, those gaskets do need to be on the outside. They have a fairly high melting point, around 600F I think and I've never had one melt or break down on me. That said, if you're using a high pressure burner on a small pot, the flames can lick up over the bottom of the pot if you crank it up too high. I tend to keep those types of burners turned down a bit to avoid damaging the gaskets. It is still high enough for a strong boil on a full pot. Low pressure burners shouldn't have that problem.

Reply
Inaccurate
Jakob F on Feb 8, 2018
Purchased on Dec 20, 2017

Mine work great with gasket, washer, and nut on the inside of the tank. Although, set up in this way, the threads also have to be sealed- I'm guessing that is where your leakage is occurring. Therefore, I also use teflon thread tape on the threads since the gasket only seals against the side of the tank. If your set up would allow for the fitting and gasket to be installed from the inside with washer and nut on the outside, then you should have no leakage at all with gasket only.

Reply
Inaccurate
Kevin M Reeves on Nov 22, 2020
Purchased on Jan 8, 2020

Since my gasket is an inch or so above the kettle base, it doesn't get hot enough to melt. The gasket temperature is a litter higher than the boiling point (the wort temperature can not go higher than 212 degrees thus the gasket temperature is limited to about 212). This assumes your flame isn't high enough to extend past the kettle base.

Reply
Inaccurate
Karl S on Feb 8, 2018
Purchased on Dec 20, 2017

If your hole is too low, the gasket may not seal because the inside bottom of the kettle may be curved. The gasket could be damaged from the burner's heat, but you can put a thin piece of stainless or other non- burnable metal slid under the kettle as a shield from flame/heat. It will work. Brew on.

Reply
Inaccurate
Jeff M on Feb 8, 2018
Purchased on Dec 20, 2017

Some kettles are finicky... I had the same problem happen to me as well. If you can get another high temp gasket and use it on both ends the outside gasket should not be affected too much by the heat. Hope this helps.

I use mine on the outside, but my HLT and BK are electric. Heat wise it takes the same to boil no matter the heat source. Only concern would be direct contact to flame.

Reply
Inaccurate
Charles Leedy on Feb 9, 2018
Purchased on Dec 20, 2017

I have used in similar situations without problem of melting. You can put a small piece of metal as a heat shield also

Reply
Inaccurate
karl h on Feb 8, 2018
Purchased on Dec 20, 2017

Vote for the best answer above!

I can not get a 1" hole drilled in my keg to install. Any suggestions? Do the SS bulkheads come with 1/2" body so I can go with a smaller hole?

Kenneth Fort on Jun 9, 2020

BEST ANSWER: There are some other weldless fittings by Blichmann that have a 1/2" or 5/8" OD threading. Or you can make your own. You will be looking for pipe fittings that have a 3/8" ID and that will allow you to use a smaller hole.

Reply
Inaccurate
Malcolm lieban Staff on Jun 9, 2020

Reply
Inaccurate
Malcolm lieban Staff on Jun 9, 2020

I would recommend using a cobalt step bit with a 1/2" chuck. I drill a 1/8" hole with high speed drill bit and then move to step bit. I also use dish washing detergent and water solution in a spray bottle for lubricant/coolant. Oil does not dissipate the heat.

Reply
Inaccurate
Kevin M Reeves on Nov 22, 2020
Purchased on Jan 8, 2020

You can drill it yourself with a conical high-speed drill bit. The deeper you go, the wider diameter hole you get. Just have to be careful not to go too deep. I did this with no problem. Just do a search for the bit.

Reply
Inaccurate
William G on Sep 16, 2020
Purchased on Nov 11, 2019

If I remember right the bulk head comes with a 7/8" bulk head and will not install on a 1/2" hole. Use a step bit to drill the hole

Reply
Inaccurate
Dave S on Sep 17, 2020
Purchased on Mar 21, 2019

Buy a 1" hole saw for metal. Should work better than just a drill bit

Reply
Inaccurate
Mark on Sep 15, 2020
Purchased on Feb 11, 2019

Vote for the best answer above!

I received the bulkhead and it only has one gasket. I am using this on a boil kettle. Should the gasket be inside or outside the kettle?

TedR on Nov 11, 2020

BEST ANSWER: We recommend putting the red silicone gasket on the outside as that tends to get the best results. We've seen people have success with both options though.

Reply
Inaccurate
Malcolm lieban Staff on Dec 2, 2020

BEST ANSWER: We recommend putting the red silicone gasket on the outside as that tends to get the best results. We've seen people have success with both options though.

Reply
Inaccurate
Malcolm lieban Staff on Dec 2, 2020

I have 3 of these and have the gasket on the inside. I have had leaks but nothing that hasnt been fixed by simply tightening it. It needs to be on pretty tight, at least for me as I have it in a 60 gallon mash tun.

Reply
Inaccurate
Vielka Garcia Pty 46515 on Dec 2, 2020
Purchased on Jan 12, 2019

Yes inside the kettle

Reply
Inaccurate
john breithaupt on Dec 2, 2020
Purchased on Apr 24, 2018

Outside

Reply
Inaccurate
Jack B on Dec 2, 2020
Purchased on Dec 3, 2018

Vote for the best answer above!

What is the OD of the 1/2” FPT side of the bulkhead?

Bradley Panasiti on Aug 28, 2021

BEST ANSWER: The outer diameter of the 1/2" FPT side (Threaded on both outside and inside) is 0.98" or roughly 1 inch.

Reply
Inaccurate
Steve C on Aug 29, 2021
Purchased on Apr 6, 2020

BEST ANSWER: The outer diameter of the 1/2" FPT side (Threaded on both outside and inside) is 0.98" or roughly 1 inch.

Reply
Inaccurate
Steve C on Aug 29, 2021
Purchased on Apr 6, 2020

the threads are 1" and the nut flange and washers measure 1-1/2 inch

Reply
Inaccurate
rick h on Aug 29, 2021
Purchased on Apr 24, 2020

Just under an inch (.9955”)

Reply
Inaccurate
MATTHEW J Z on Aug 28, 2021
Purchased on May 13, 2020

Vote for the best answer above!

Will this fit as a direct replacement for the digiboil (7 gallon) outlet valve?

Doug Haviland on Aug 17, 2021

BEST ANSWER: I measured my 7 gal digiboil and the hole in the side is 0.85" (21mm). The digiboil hole has a pressed flange in the metal around the hole so I don't think it would work even if you enlarged the hole to 1" for this bulkhead.

Reply
Inaccurate
Ross T on Aug 17, 2021
Purchased on Feb 6, 2020

Reviews

Review More Purchases | My Posts

4.8 / 5.0

13 Reviews

5 Stars

4 Stars

3 Stars

2 Stars

1 Star

Rated 4 out of 5

Almost Perfect

The Bulkhead hardware was exactly what I needed for use on a stainless steel pot (thin metal). My only suggestion is to make sure you have a silicone washer to help in sealing. The rubber washer did not conform perfectly. I added a very small amount of 100% silicone RTV and the washer sealed.

Was this review helpful? Yes (0) No (0)
Flag as Inappropriate

March 15, 2021

JRock

Purchased
1 year ago

Was this review helpful? Yes (0) No (0)
Flag as Inappropriate

Rated 5 out of 5

Perfect for Brewzilla

Used this to install a sight gauge on my Brewzilla. Love it.

Was this review helpful? Yes (0) No (0)
Flag as Inappropriate

December 16, 2020

Wayne F

Purchased
1 year ago

Was this review helpful? Yes (0) No (0)
Flag as Inappropriate

Rated 5 out of 5

No Leaks

Easy to install and no leaks. The gasket has a groove that it sits in some when you tighten it it does slide out of place.

Was this review helpful? Yes (0) No (0)
Flag as Inappropriate

August 12, 2020

Ben Wells

Purchased
over 2 years ago

Was this review helpful? Yes (0) No (0)
Flag as Inappropriate

Rated 5 out of 5

Through-wall for mash screen

wanted to add a 12"mash screen to my 30 and 55 gallon brew kettles. I enlarged the holes that are on my Blichmann kettles for these and it worked out great.

Was this review helpful? Yes (0) No (0)
Flag as Inappropriate

May 26, 2020

Jeffrey K

Purchased
over 2 years ago

Was this review helpful? Yes (0) No (0)
Flag as Inappropriate

Rated 5 out of 5

Good Quality!

This is a well made piece and seems to be a good value! It makes it easier to modify a tank if you are not a welder.

Was this review helpful? Yes (0) No (0)
Flag as Inappropriate

May 17, 2020

Jeff Benson B

Purchased
over 2 years ago

Was this review helpful? Yes (0) No (0)
Flag as Inappropriate

Rated 5 out of 5

Nice fittings!

Great quality fittings. I installed these on my HLT and like the flat gasket much better than other fittings I have, from another company, that came with o-rings and nuts without the o-ring retaining groove. So far, these gaskets have stayed in place.

Was this review helpful? Yes (0) No (0)
Flag as Inappropriate

January 31, 2020

Kevin M Reeves

Purchased
over 2 years ago

Was this review helpful? Yes (0) No (0)
Flag as Inappropriate

Rated 4 out of 5

Got a spare rubber gasket?

Quality product with limited instructions. Technical support wasn’t firm on whether the rubber gasket went inside or out, their best guess was put one on both inner and outer…